surface mount lc filters document 124-1 document 124-1 revised 01/16/14 these space saving low and high pass flters are pre- tuned, tight tolerance modules that serve a wide variety of fltering requirements. ? 3rd order butterworth alignment ? 50 ohm characteristic impedance; less than 0.3 db insertion loss low pass filters part number 1 -3 db cutoff i rms (ma) 2 s3lp156l_ 15 mhz 200 s3lp306l_ 30 mhz 300 s3lp606l_ 60 mhz 300 s3lp157l_ 150 mhz 400 s3lp307l_ 300 mhz 400 s3lp507l_ 500 mhz 500 s3lp707l_ 700 mhz 500 s3lp807l_ 800 mhz 500 s3lp907l_ 900 mhz 500 s3lp108l_ 1.0 ghz 500 s3lp128l_ 1.2 ghz 500 s3lp158l_ 1.5 ghz 500 s3lp188l_ 1.8 ghz 500 s3lp218l_ 2.1 ghz 500 visit rf inductors C color coding for color coding explanation. 0.205 5,21 0.160 4,06 0.180 4,57 0.020 0,51 0.125 3,18 0.070 1,78 0.120 3,05 max max pa rt marking 2nd digit (o v er p1) multiplier (10) (o v er p2) 1st digit (o v er p3) 0.085 2,16 max 0.040 1,02 recommended land p attern 0.055 1,40 0.050 1,27 0.040 1,02 0.045 1,14 p1 p2 p3 1. when ordering, please specify packaging code: s3hp156l c packaging: c = 7 machine-ready reel. eia-481 embossed plastic tape (600 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d = 13 machine-ready reel. eia-481 embossed plastic tape (2200 parts per full reel). 2. current that causes a 15c rise from 25c ambient. 3. operating temperature range -40c to +85c. 4. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering high pass filters part number 1 -3 db cutoff i rms (ma) 2 s3hp156l_ 15 mhz 300 s3hp306l_ 30 mhz 300 s3hp606l_ 60 mhz 300 s3hp157l_ 150 mhz 300 s3hp307l_ 300 mhz 300 s3hp507l_ 500 mhz 500 s3hp807l_ 800 mhz 500 designers kit d302 contains 3 of each value terminations rohs compliant silver over copper or gold over nickel over silver weight 64.7 C 69.0 mg ambient temperature C40c to +85c storage temperature component: C40c to +85c. tape and reel packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 12 per billion hours / 83,333,333 hours, calculated per telcordia sr-332 packaging 600/7 reel; 2200/13 reel paper tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 2.3 mm pocket depth pcb washing tested to mil-std-202 method 215 plus an additional aqueous wash. see doc787_pcb_washing.pdf .
document 124-2 frequency responselow pass filters* frequency responsehigh pass filters* *measured on agilent/hp 8753d network analyzer 1 10 100 frequency (mhz) db atten uation (re: 50 ) 20 0 40 60 80 s3hp-606 s3hp-306 s3hp-156 10 100 1000 frequency (mhz) db atten uation (re: 50 ) 10 0 20 30 40 s3hp-807 s3hp-507 s3hp-307 s3hp-157 10 100 1000 frequency (mhz) db atten uation (re: 50 ) 20 0 40 60 80 s3lp-156 s3lp-306 s3lp-606 100 1000 10000 frequency (mhz) db atten uation (re: 50 ) 10 0 20 30 40 s3lp-157 s3lp-307 s3lp-507 s3lp-807 100 1000 10000 frequency (mhz) db atten uation (re: 50 ) 10 20 30 40 0 s3lp-907 s3lp-707 s3lp-128 100 1000 10000 frequency (mhz) db atten uation (re: 50 ) 10 0 20 30 40 s3lp-188 s3lp-158 s3lp-218 document 124-2 revised 01/16/14 in out in out l1 l2 l1 c1 c2 c1 lo w pass filter high pass filter p3 p3 p2 p2 p1 p1 surface mount lc filters
|